Interior
Cost to Widen a Doorway in 2026: Average Prices & Labor
Widening a doorway costs an average of $1,200 nationwide in 2026, with most projects falling between $600 and $2,000. Structural load-bearing headers, exterior masonry, and electrical rerouting can push totals up to $19,000.
Updated November 12, 2026 · 14 min read · US Home Costs editorial desk
Planning range
Assumes widening a single standard residential doorway from 28–30 inches to 36 inches, including framing materials, basic drywall patching, trim, and professional carpenter labor, with a national average of $1,200.
Typical planning range $600 to $2,000. National spread $50 to $19,000.
- DIY or hire
- Confident DIYers can widen a simple non-load-bearing drywall opening for $50 to $300 in materials, provided no wiring or plumbing runs through the wall. Load-bearing walls, exterior openings, and structural header installations require a licensed contractor and structural engineer.
- Repair or replace
- Keep and reuse an existing door slab only if you are adding trim or a sidelight; otherwise, widening a doorway requires replacing the door slab, jamb, and casing to fit the new rough opening. If the existing framing has rot or shifting, full replacement of the header and jack studs is mandatory.
The national average cost to widen a doorway in 2026 is $1,200, with most homeowners spending between $600 and $2,000 for a standard interior expansion. Across all project scopes, the total cost to widen a door opening ranges from as little as $50 for a minor DIY trim and jamb adjustment on a non-load-bearing partition up to $19,000 or more for a complex structural renovation involving an exterior brick or concrete wall, long-span steel beams, and utility relocation. Whether you are updating a narrow hallway for wheelchair accessibility or opening a cramped kitchen passage into a dining room, the final price depends primarily on whether the wall supports the weight of the roof or upper floors.
Cost to widen a doorway at a glance
Planning a doorway expansion starts with identifying the wall type and target width. Moving from a standard 28-inch or 30-inch interior passage to a 36-inch accessible doorway requires reframing the rough opening, installing a new header, and patching surrounding wall finishes.
| Project Scope / Doorway Type | Typical Cost Range | National Average | Typical Timeline |
|---|---|---|---|
| Minor DIY Trim / Jamb Adjustment (Non-Load-Bearing) | $50 – $300 | $175 | 1 day |
| Standard Interior Doorway (Non-Load-Bearing) | $300 – $1,200 | $750 | 1 – 2 days |
| Load-Bearing Interior Doorway (New Wood/LVL Header) | $1,200 – $6,000 | $3,200 | 2 – 4 days |
| Double Doorway / Wide Pass-Through (48 to 60 inches) | $1,500 – $4,500 | $2,800 | 2 – 3 days |
| ADA / Wheelchair Accessible Doorway Conversion | $2,000 – $6,500 | $3,800 | 2 – 5 days |
| Exterior Wood-Frame Doorway Expansion | $2,500 – $7,500 | $4,800 | 3 – 5 days |
| Complex Structural / Exterior Masonry or Steel Beam | $6,000 – $19,000+ | $11,500 | 1 – 2 weeks |
What moves the price
Several structural, mechanical, and aesthetic factors determine where a project lands within the $50 to $19,000 range. Understanding these variables helps prevent mid-project budget surprises once drywall or siding is opened.
Load-bearing vs. non-load-bearing walls
The single largest cost driver is structural load. A non-load-bearing partition wall only supports its own weight, allowing a carpenter to cut out existing studs and frame a wider opening for $300 to $1,200 without temporary support walls. In contrast, the cost to widen a doorway in a load-bearing wall ranges from $1,200 to $6,000 because the wall carries weight from ceiling joists, second-story floors, or roof trusses. Before cutting any framing, workers must build temporary shoring walls on both sides of the opening, calculate the proper header span, and install a heavy-duty solid lumber, laminated veneer lumber (LVL), or steel beam supported by additional jack and king studs.
Interior vs. exterior walls
The cost to widen an interior doorway stays lower because contractors only deal with interior drywall, hollow-core or solid-core interior doors, and baseboard trim. The cost to widen an exterior doorway climbs quickly—typically $2,500 to $19,000+—because exterior walls are almost always load-bearing and require weatherproofing, insulation, structural sheathing, exterior siding or brick repair, flashing, and an insulated exterior-grade door unit with a sloped threshold. Cutting through brick, stone veneer, or poured concrete foundation walls requires specialized masonry saws and steel lintels, driving labor hours up dramatically.
Target opening width and configuration
Expanding a 30-inch doorway to 36 inches involves minimal framing adjustments if an existing header already spans close to that distance, though a new header is still required whenever the rough opening increases. Creating a double doorway or open pass-through measuring 48 to 60 inches wide costs $1,500 to $4,500 on interior walls and even more on load-bearing spans. Wider spans concentrate heavier downward loads onto the studs at each end of the opening, which sometimes requires reinforcing the subfloor or adding blocking down to the basement or crawlspace foundation.
ADA and wheelchair accessibility requirements
The cost to widen a doorway for a wheelchair generally runs between $2,000 and $6,500. Under Americans with Disabilities Act (ADA) residential guidelines and universal design best practices, a doorway must provide at least 32 inches of clear width when the door is open at a 90-degree angle, which usually requires installing a 36-inch door slab. Beyond framing, accessibility upgrades often include installing offset swing-clear hinges (which add 1.5 to 2 inches of clearance without full reframing in borderline cases), lever-style door handles, zero-step beveled thresholds, and widening adjacent hallway turning radii.
Hidden utilities inside the wall
Wall cavities adjacent to doorways are prime locations for light switches, electrical outlets, HVAC return ducts, and plumbing lines. Rerouting a single light switch box to sit beside the new wider trim adds $150 to $450 to the bill. However, if opening the wall reveals a main plumbing stack, pressurized water supply lines, or ductwork, costs escalate rapidly. Moving a drain-waste-vent stack or supply line can add $500 to $2,500+, similar to the labor involved in a focused plumber-cost service call or localized burst-pipe-repair intervention.
Wall finish materials and trim matching
Standard 1/2-inch gypsum drywall is inexpensive to patch, tape, and texture, typically adding $150 to $500 for a small opening. Older homes with plaster and lath walls require specialized patching techniques or skim-coating to blend seamless transitions, adding $300 to $900. Matching historic wood moldings, custom stained oak casing, or tall multi-piece baseboards also increases material and finish carpentry costs compared to standard paint-grade pine or MDF trim.
Cost by wall type and doorway size
Evaluating costs by specific structural category and final opening width provides a clearer picture of material and engineering requirements.
| Doorway Category / Size | Framing & Header Cost | Door Unit & Hardware | Drywall, Trim & Finish | Total Installed Range |
|---|---|---|---|---|
| 30" to 36" Non-Load-Bearing Interior | $150 – $450 | $100 – $400 | $50 – $350 | $300 – $1,200 |
| 30" to 36" Load-Bearing Interior | $600 – $2,500 | $200 – $800 | $400 – $1,200 | $1,200 – $4,500 |
| 48" to 60" Double Interior Opening | $700 – $2,200 | $400 – $1,400 | $400 – $900 | $1,500 – $4,500 |
| 32" to 36" ADA Wheelchair Conversion | $800 – $2,800 | $350 – $1,200 | $500 – $1,500 | $2,000 – $6,500 |
| 36" Exterior Wood-Framed Entry | $1,000 – $3,000 | $800 – $2,500 | $700 – $2,000 | $2,500 – $7,500 |
| 60"+ Exterior Patio / French Doorway | $2,500 – $8,000 | $1,800 – $5,500 | $1,200 – $3,500 | $5,500 – $17,000+ |
Cost per unit and hourly labor rates
While contractors normally quote doorway expansions as a flat project price, breaking down the underlying unit rates helps homeowners audit itemized estimates.
| Cost Component | Unit of Measurement | National Average Rate | Notes |
|---|---|---|---|
| General Contractor Management | Per hour | $50 – $150 | Oversees permits, structural trades, and scheduling |
| Finish / Framing Carpenter | Per hour | $35 – $100 | Handles demolition, framing, hanging doors, and trim |
| Structural Engineer Consultation | Per visit / report | $300 – $800 | Required for load-bearing headers and permit stamps |
| Drywall & Paint Finishing | Per square foot | $1 – $3 | Applies to patching, taping, mudding, and priming |
| LVL / Engineered Lumber Header | Per linear foot | $8 – $20 | Material only; varies by beam depth (9.5" to 14") |
| Interior Pre-Hung Door Unit | Per unit | $150 – $650 | Hollow-core sits at low end; solid wood at high end |
| Exterior Pre-Hung Door Unit | Per unit | $500 – $2,500+ | Fiberglass, steel, or wood with weatherstripping |
Labor vs. materials breakdown
For an average $1,200 interior doorway expansion, labor accounts for roughly 60% to 70% ($720 to $840) of the total cost, while materials make up 30% to 40% ($360 to $480).
- Materials ($360 – $480 typical): Dimensional 2x4 or 2x6 framing lumber, header stock (double 2x8s, 2x10s, or LVL), structural fasteners and joist hangers, drywall sheets, joint compound, corner bead, shims, a pre-hung door unit, casing trim, and primer/paint.
- Labor ($720 – $840 typical): Site protection (plastic dust barriers and floor runners), careful removal of existing trim and drywall, cutting framing, building temporary supports if load-bearing, installing the new header and jamb, hanging and leveling the door, drywall mudding across multiple coats, sanding, and trim installation.
On complex load-bearing or exterior masonry projects, the labor share often rises to 75% or more because multi-stage drywall drying times, structural shoring, and masonry cutting require multiple site visits over several days.
Hidden and extra costs to budget for
Beyond basic carpentry and drywall, several secondary expenses frequently appear on final invoices:
- Building permits ($50 – $500): Most municipalities do not require a permit for a cosmetic non-load-bearing trim change, but virtually all jurisdictions require a building permit when altering a load-bearing header, modifying an exterior wall, or relocating electrical wiring.
- Structural engineer evaluation ($300 – $800): When widening a load-bearing wall beyond 36 to 48 inches, local building departments commonly require stamped engineering drawings specifying header dimensions, jack stud counts, and load paths to the foundation.
- Flooring patching ($150 – $1,000+): Removing wall framing exposes bare subfloor where the bottom plate once sat. Hardwood planks must be toothed in and refinished, carpet may need stretching or a transition strip, and tile requires matching replacements. Homes with radiant-floor-heating require extreme caution during demolition and subfloor fastening so embedded tubing or electric mats are not punctured.
- Electrical switch relocation ($150 – $450): Light switches are almost always mounted 4 to 6 inches from the edge of the door casing. Widening the doorway by 6 inches means moving the electrical box further down the wall, which may require splicing longer Romex wire in the attic or basement if existing slack is insufficient.
- Asbestos or lead paint testing and abatement ($200 – $1,500+): In homes built before 1978, disturbing older painted trim or plaster joint compound may trigger lead-safe containment protocols or asbestos testing before demolition begins.
DIY or hire
Deciding whether to tackle a doorway expansion yourself or hire a professional hinges entirely on structural risk and finish expectations.
When DIY makes sense
A homeowner with solid carpentry skills, a circular saw, a reciprocating saw, a level, and drywall finishing tools can widen a non-load-bearing interior doorway for $50 to $300 in materials. DIY is viable when:
- You have verified in the attic or basement that ceiling joists run parallel to the wall and no roof trusses or upper walls rest on it.
- No electrical switches, outlets, plumbing pipes, or HVAC ducts sit within the widened footprint.
- You are converting a doorway into an open cased pass-through (no door slab to hang), which eliminates the tricky task of mortising hinges and aligning a latch strike plate.
When to hire a pro
Hiring a licensed general contractor or experienced finish carpenter is essential when:
- The wall is load-bearing or exterior: Miscalculating header size or failing to properly shore the ceiling during demolition can cause sagging floors, cracked upstairs drywall, or structural failure.
- You are hanging a new heavy door: A door that is out of plumb by even 1/8 inch will swing open on its own, bind against the jamb, or fail to latch.
- Utilities must be moved: Rerouting 120-volt wiring or plumbing lines requires licensed trades to meet local building codes and pass inspection.
- You are remodeling adjacent rooms: If you are already planning a larger kitchen-remodel or bathroom-remodel, bundling the doorway expansion into the main contractor's scope saves mobilization fees and ensures cohesive flooring and trim transitions.
Repair or replace
When widening a doorway, homeowners sometimes ask whether they can salvage existing components to trim costs.
- Door slab and jamb: If you are widening the opening from 30 inches to 36 inches, the old 30-inch door slab and header jamb cannot be stretched. You must replace them with a wider pre-hung door unit or a custom-built jamb and wider slab. The only exception is adding a narrow fixed sidelight panel alongside an existing exterior door, which still requires a new wider frame assembly.
- Interior casing and trim: Carefully prying off existing wood casing with a wide putty knife allows you to reuse the two vertical side pieces, though you will need to purchase a longer horizontal head casing piece to span the wider top edge.
- Existing framing: If demolition uncovers water-damaged sill plates, termite damage, or bowed studs, repairing sistered studs is insufficient—replace the compromised framing members completely before installing the new header.
How to save money on widening a doorway
You can reduce the cost to expand a doorway without compromising structural safety or finish quality by applying several practical strategies:
- Use swing-clear hinges for minor accessibility gains: If your sole goal is getting a wheelchair or walker through a 30-inch or 32-inch doorway and you only need an extra 1.5 to 2 inches of clearance, installing offset swing-clear hinges ($25 to $60 per set) moves the open door completely out of the doorway path without tearing out a single stud.
- Create a cased opening instead of installing a door: Removing the door slab and hardware entirely—turning a narrow kitchen or dining doorway into an open cased pass-through—saves $150 to $650 on the door unit plus labor for hinge and lockset installation.
- Handle demolition, painting, and cleanup yourself: Ask your contractor if you can remove existing trim, strip drywall back to the nearest studs, haul away debris, and handle final priming and painting. Sweat equity on non-structural prep and finishing can trim $200 to $500 off labor charges.
- Choose standard door sizes: Stick to standard stock widths (32 inches or 36 inches for single doors; 48 or 60 inches for double doors) rather than custom odd-inch widths, which require special-order slabs and carry steep manufacturer markups.
- Schedule alongside other drywall or carpentry work: Because drywall mud requires 24 hours of drying between coats, contractors build multiple trip charges into small standalone jobs. Combining a doorway widening with other interior repairs spreads setup and travel time across multiple tasks.
How to hire a contractor and questions to ask
Collect at least three itemized written estimates from licensed carpenters or general contractors who regularly perform structural framing and interior remodeling. Avoid vague lump-sum quotes that fail to specify header sizing, drywall finishing levels, or permit handling.
Ask every prospective contractor these specific questions before signing a contract:
- How will you verify whether this wall is load-bearing before demolition begins? Look for a clear plan involving attic or basement joist inspection rather than guesswork.
- What header material and dimensions are included in your quote? Ensure the estimate specifies exact lumber dimensions (such as double 2x10s or a specific LVL beam size) and proper jack stud support.
- Are building permits and structural engineering fees included in the total price? Clarify who pulls the permit and schedules municipal inspections.
- How will you contain dust and protect adjacent flooring during demolition? Drywall and plaster dust travel easily; professional crews use zipper plastic barriers and floor protection.
- Does your quote include moving nearby light switches, patching subflooring, and painting the finished trim? Knowing where the carpenter's scope ends prevents surprise change orders.
Regional and climate considerations
Labor rates and construction methods vary across the United States, shifting total project costs by 15% to 35% from the national average:
- Northeast and West Coast metros: Higher hourly rates for carpenters ($75 to $125/hr) and stricter municipal permitting in cities like New York, Boston, San Francisco, and Seattle push typical load-bearing doorway projects toward $2,500 to $7,500+. Older housing stock in the Northeast also increases the likelihood of encountering plaster-and-lath walls or balloon framing.
- Midwest and South: Lower average labor rates ($35 to $75/hr) keep standard non-load-bearing interior expansions closer to $300 to $900. However, homes built on concrete slabs in Texas, Florida, and the Southwest cannot have utilities rerouted beneath the floor, meaning electrical wires or pipes found in a wall must be rerouted up through the attic.
- Cold-climate regions: When widening an exterior doorway in northern states, contractors must pay strict attention to continuous air sealing, high-density foam insulation around the rough opening, and thermal-break thresholds to prevent winter drafts and frost buildup.
- Coastal hurricane zones: Expanding an exterior doorway in Florida or along the Gulf and Atlantic coasts requires impact-rated exterior door assemblies and heavy-duty structural anchorage to meet wind-load building codes, adding $800 to $2,500 in material and hardware costs.
Signs you need to widen a doorway
Homeowners typically pursue a doorway expansion when functional bottlenecks or safety concerns outweigh the disruption of short-term construction:
- Mobility and aging-in-place needs: Walkers, standard wheelchairs (typically 24 to 27 inches wide), and power chairs require at least 32 inches of clear opening width—and ideally a 36-inch door—to pass through without scraped knuckles or damaged door frames.
- Appliance and furniture clearance: Modern French-door refrigerators, front-loading washers, and large sectional sofas frequently measure 33 to 36 inches deep, making it impossible to move them through older 28-inch or 30-inch kitchen and laundry doorways without removing doors and jambs.
- Cramped traffic flow and poor natural light: Narrow doorways between kitchens, dining areas, and living rooms create congestion during gatherings and block natural daylight from reaching interior hallways.
- Existing framing or jamb damage: If a narrow doorway already suffers from split jambs, warped framing, or settled headers from decades of household wear, widening the opening lets you replace damaged components while upgrading functionality at the same time.
Common questions
Answers describe national planning ranges, not your house.
How much does it cost to widen a doorway in a load-bearing wall?
Widening a doorway in a load-bearing wall costs between $1,200 and $6,000 for most interior projects, with a national average around $3,200. The higher cost covers temporary shoring walls, a structural engineer's evaluation ($300 to $800), building permits ($50 to $500), and installing an engineered LVL or solid wood header to carry the weight above the opening.
How much does it cost to widen a doorway for a wheelchair?
The average cost to widen a doorway for wheelchair accessibility ranges from $2,000 to $6,500. To meet ADA clear-width standards of at least 32 inches when the door is open 90 degrees, contractors typically reframe the opening to fit a 36-inch door slab, relocate adjacent light switches, and install a low-profile beveled threshold.
Can I widen a doorway without a permit?
You generally do not need a permit for minor non-load-bearing trim adjustments or enlarging an interior partition opening that contains no wiring or plumbing, though rules vary by city. However, a building permit ($50 to $500) is almost always required if you alter a load-bearing wall, modify an exterior wall, or relocate electrical switches and plumbing lines.
Is it cheaper to widen an interior doorway or an exterior doorway?
Widening an interior doorway is significantly cheaper, averaging $300 to $1,200 for non-load-bearing walls and $1,200 to $6,000 for load-bearing walls. Widening an exterior doorway typically costs $2,500 to $19,000 or more because exterior walls carry roof loads and require weatherproofing, insulation, siding or masonry repair, and an insulated exterior door unit.
How long does it take to widen a doorway?
A simple non-load-bearing interior doorway takes 1 to 2 days to reframe, hang, and trim. Load-bearing interior walls, wheelchair-accessible conversions, and exterior doorway expansions typically take 2 to 5 days—or up to 2 weeks for exterior brick or structural steel—due to engineering approvals, utility relocation, and multi-coat drywall drying times.
Related cost guides
Ranges for work that often shows up in the same season as this project.
- InteriorAccent Wall Cost in 2026: Prices by Type and MaterialAn accent wall costs between $140 and $1,840 nationally in 2026, with most painted projects falling between $718 and $1,840 depending on wall size, prep work, and finish complexity.Typical planning range $718 to $1,840.Typical range
- InteriorDoor Frame Repair Cost in 2026: Prices by TypePlanning a door frame or jamb repair? Explore national 2026 cost figures for minor patches, rotted wood repairs, kick-in fixes, and full frame replacements.Typical planning range $100 to $325.Typical range
- InteriorGarage Cabinets Cost in 2026: Prices by Type and MaterialPlan your garage storage project with updated 2026 national cost data covering materials, garage sizes, and installation labor.Typical planning range $505 to $2,164.Typical range
- InteriorMirror Installation Cost in 2026: Complete Price GuideInstalling a mirror costs $140 to $430 for most home projects in 2026, with a national average of $240. Explore full pricing details for LED, gym, and custom wall mirrors.Typical planning range $140 to $430.Typical range
