Skip to content
US Home Costs

Exterior

Siding Replacement Cost in 2026: Prices by Size & Material

Replacing house siding in 2026 typically costs $10,000 to $32,500 for a standard 2,500-square-foot exterior wall area, with full-project national ranges spanning $3,600 to $45,500.

Updated November 12, 2026 · 17 min read · US Home Costs editorial desk

Planning range

Figures represent 2026 US national planning ranges for a whole-house siding replacement including standard materials and professional installation labor, with typical totals reflecting 2,500 square feet of exterior wall area (not interior floor square footage).

Typical planning range $10,000 to $32,500. National spread $3,600 to $45,500.

DIY or hire
DIY siding installation can save $2 to $6 per square foot in labor, but working safely on two-story scaffolding, flashing windows properly, and cutting fiber cement or metal panels require specialized tools and experience.
Repair or replace
Spot repairs make financial sense when damage is isolated to a few cracked boards or a single wind-damaged wall, whereas widespread rot, warped sheathing, or rising heating and cooling bills point toward a full replacement.

In 2026, the national siding replacement cost typically falls between $10,000 and $32,500, with a national average near $21,250 for a standard 2,500-square-foot exterior wall surface. Across all home sizes and cladding materials, the full cost to replace siding on a house spans $3,600 to $45,500 installed, or $4 to $13 per square foot for most residential projects, and up to $18 per square foot for premium natural stone, cedar, or brick veneer. One of the most common points of confusion when budgeting is how contractors measure a home: siding is priced by exterior wall square footage, not interior living floor space. Accounting for old siding removal, house wrap, trim, and architectural complexity early prevents unexpected surprises once estimates arrive.

Siding replacement cost at a glance

Use this national planning summary to benchmark contractor bids for a whole-house re-side in 2026. All figures combine standard cladding materials and professional installation labor for a typical residential home, before major structural sheathing repairs or custom architectural trim packages.

Cost Category2026 National Planning RangeTypical Basis / Notes
Whole-House Replacement (All Sizes)$3,600 – $45,500Covers 900 to 3,500 sq ft of exterior wall area
Typical Whole-House Project$10,000 – $32,500Based on 2,500 sq ft of net exterior wall area
National Average Project Total~$21,250Mid-range material on an average single-family home
Installed Cost per Square Foot$4 – $13 / sq ftUp to $15–$18 / sq ft for fiber cement, cedar, or brick
Old Siding Removal & Disposal$0.70 – $2.00 / sq ftAdds $1,750 – $5,000 on a 2,500 sq ft wall area
Trim, Soffits & Fascia$1,500 – $4,500Often priced separately by linear foot
House Wrap & Rigid Insulation$0.50 – $2.50 / sq ftVaries by weather barrier grade and foam thickness

Siding replacement cost by home size

When homeowners ask how much does it cost to side a 1500 sq ft house, the answer depends on whether "1,500 sq ft" refers to the interior floor plan or the exterior wall surface. A single-story 1,500-square-foot ranch home typically has around 1,300 to 1,600 square feet of net exterior wall area once windows and doors are subtracted, whereas a two-story 1,500-square-foot home often has 1,800 to 2,100 square feet of exterior wall surface.

Because contractors calculate bids strictly from exterior wall area, matching your wall square footage—rather than your real estate listing square footage—gives a far more reliable siding replacement cost estimator baseline.

Exterior Wall AreaComparable Home ProfileLow-End Total ($4/sq ft)Mid-Range Total ($8.50/sq ft)High-End Total ($13/sq ft)
900 sq ftSmall cottage, bungalow, or detached ADU$3,600$7,650$11,700
1,500 sq ftSingle-story 1,500 sq ft ranch home$6,000$12,750$19,500
2,000 sq ftCompact two-story or larger ranch home$8,000$17,000$26,000
2,500 sq ftAverage US single-family two-story home$10,000$21,250$32,500
3,500 sq ftLarge two-story home with gables and dormers$14,000$29,750$45,500

How to estimate your exterior wall square footage

You can build an accurate pre-quote wall measurement in ten minutes using a tape measure and basic geometry before scheduling contractor walkthroughs:

  1. Measure the perimeter: Walk the exterior foundation and measure the length of every wall section, adding them together to get total linear feet.
  2. Multiply by wall height: Multiply the perimeter by the height from the bottom of the existing siding to the roofline eaves (typically 9 to 10 feet for one story, or 18 to 20 feet for two stories).
  3. Add gable ends: For triangular attic gables, multiply the base width by the peak height and divide by 2, then add each gable to your total.
  4. Subtract openings: Measure standard windows (typically 15 square feet each) and exterior doors (about 20 square feet each) and subtract that total from your gross wall area to find net wall square footage.
  5. Add a 10% waste factor: Contractors order 10% to 15% extra material to account for diagonal gable cuts, window cutouts, and starter strips.

House siding cost by material

Material selection is the largest driver of house siding cost, creating a fourfold price spread between basic builder-grade vinyl and natural stone or brick veneer. Each cladding type balances upfront installation price against lifespan, fire resistance, paint cycles, and regional weather durability.

Siding MaterialInstalled Cost / Sq Ft1,500 Sq Ft Wall Total2,500 Sq Ft Wall TotalExpected LifespanMaintenance Profile
Vinyl Siding$4 – $12$6,000 – $18,000$10,000 – $30,00020 – 40 yearsLow; periodic washing, never needs paint
Aluminum / Metal Siding$6 – $10$9,000 – $15,000$15,000 – $25,00030 – 50 yearsLow; resists fire and insects, can dent
Fiber Cement Siding$6 – $15$9,000 – $22,500$15,000 – $37,50030 – 50+ yearsModerate; repaint every 10–15 years
Engineered Wood Siding$7 – $12$10,500 – $18,000$17,500 – $30,00020 – 30 yearsModerate; repaint every 10–15 years
Natural Cedar Siding$6 – $16$9,000 – $24,000$15,000 – $40,00020 – 40 yearsHigh; stain or seal every 3–5 years
Brick Veneer Siding$8 – $18$12,000 – $27,000$20,000 – $45,00050 – 100 yearsVery low; occasional mortar tuckpointing
Stucco Siding$7 – $15$10,500 – $22,500$17,500 – $37,50040 – 60 yearsLow to moderate; hairline crack sealing

Vinyl siding

Standard vinyl remains the most budget-friendly whole-house option at $4 to $12 per square foot installed, with insulated foam-backed vinyl sitting at the upper end of that range. It installs quickly over flat wall runs, never requires scraping or painting, and comes in horizontal lap, board-and-batten, and shake profiles. Because panels expand and contract with temperature swings, installers must leave small expansion gaps at trim joints; see our detailed vinyl-siding-installation guide for profile thickness and insulated-backing breakdowns.

Fiber cement siding

Fiber cement blends Portland cement, sand, and cellulose fibers into heavy, non-combustible planks and panels costing $6 to $15 per square foot installed. It holds factory-applied or field-applied paint longer than natural wood, resists termites and woodpeckers, and stands up well to hail and coastal winds. Because planks weigh roughly 2.5 to 3 pounds per square foot and require silica-dust-controlled cutting, labor makes up a larger share of the bill—covered in depth in our fiber-cement-siding guide.

Engineered wood siding

Engineered wood pairs treated wood strands or fibers with moisture-resistant resins and waxes, running $7 to $12 per square foot installed. It delivers deeper wood-grain embossing than vinyl while weighing less and cutting faster than fiber cement, which helps keep installation labor moderate. Explore brand-neutral plank vs. panel specs and warranty requirements in our engineered-wood-siding-cost guide.

Natural cedar siding

Real cedar clapboards, shingles, and shakes cost $6 to $16 per square foot installed depending on wood grade (clear vertical grain costs substantially more than knotty cedar) and profile style. Cedar naturally resists rot and insects thanks to its natural oils, but it demands regular semi-transparent staining or painting to prevent graying, cupping, and moisture absorption. Compare shingle, shake, and bevel-lap pricing in our cedar-siding-cost guide.

Metal and aluminum siding

Residential metal cladding—including traditional horizontal aluminum lap and modern standing-seam or corrugated steel panels—runs $6 to $10 per square foot installed for standard aluminum and up to $12 to $16 per square foot for heavy-gauge architectural steel. Metal is fireproof, impervious to rot, and recyclable, though thinner aluminum gauges can dent from hail or ladder impacts. Review gauge ratings and finish warranties in our metal-siding-cost guide.

Brick veneer and stucco

Masonry and cementitious finishes anchor the high end of residential cladding. Thin brick veneer and traditional laid brick siding run $8 to $18 per square foot installed due to mortar work, structural ledger requirements, and slower daily square-footage output; compare full-bed and thin-brick options in our brick-siding-cost guide. Traditional three-coat and synthetic stucco systems typically run $7 to $15 per square foot installed and perform best in dry or warm climates; see lath and finish-coat breakdowns in our stucco-installation guide.

Cost per unit: square foot, square, and linear foot

Contractors mix three units of measurement on residential siding proposals, which makes line-by-line bid comparison tricky unless you convert them to a common baseline:

  • Per square foot ($4 – $13+ / sq ft): The standard consumer metric used for wall cladding, house wrap, rigid foam insulation, and old siding tear-off.
  • Per roofing/siding "square" ($400 – $1,300+ / square): Many exterior contractors still price wholesale materials and crew labor by the "square," where 1 square equals 100 square feet of wall area. A 2,500-square-foot wall surface equals 25 squares.
  • Per linear foot ($2 – $12 / linear ft): Used for narrow, continuous trim elements rather than broad wall planes. Corner boards, J-channels, window casing trim, belly bands, fascia boards, and soffit vents are almost always priced by the linear foot.

Labor vs. materials breakdown

Across a typical 2026 whole-house siding replacement, materials account for 45% to 55% of the total contract price, while labor, equipment, and disposal account for 45% to 55%. That split shifts dramatically depending on the cladding weight and installation method:

  • Lightweight interlocking panels (vinyl, aluminum): Materials often represent 50% to 60% of the bill because two installers can hang 300 to 500 square feet per day using standard snips and nail guns.
  • Heavy, nailed-and-caulked planks (fiber cement, cedar): Labor often climbs to 55% to 65% of the total cost. Fiber cement requires two-person carries on 12-foot planks, specialty carbide or shear blades, careful blind-nailing, and color-matched caulking at every butt joint and trim intersection.
  • Masonry and trowel-applied systems (brick veneer, stucco): Labor frequently exceeds 65% of the project cost due to scaffolding setup, mixing, lath installation, and multi-day curing windows.

What moves the price

Two homes with the exact same 2,500 square feet of exterior wall area can receive quotes that differ by $12,000 or more. Beyond basic cladding material choice, seven structural and site factors drive real-world contractor pricing:

  • Number of stories and roof pitch: A single-story ranch allows crews to work off stepladders and low pump jacks. Two- and three-story homes require tall pump-jack staging, roof brackets, or full scaffolding, adding $1,500 to $4,500 in setup time and height-hazard labor.
  • Architectural complexity and cut count: A simple rectangular box with four corners and standard rectangular windows installs fast. Steep dormers, turret walls, bay windows, recessed entryways, and multiple roof-to-wall intersections multiply miter cuts, flashing pieces, and material waste.
  • Profile style: Standard horizontal lap siding is the fastest and least expensive profile to install. Vertical board-and-batten requires horizontal furring strips or solid wood sheathing for nailing, while individual cedar or polymer shakes require hand-fitting row by row, adding $1.50 to $4.00 per square foot.
  • Factory finish vs. raw primed boards: Ordering fiber cement or engineered wood with a baked-on factory color finish adds $1.50 to $3.00 per square foot upfront, but it eliminates the $2,500 to $6,000 cost of hiring painters after installation and carries a longer finish warranty.
  • Insulation upgrades: Adding 1/2-inch to 1-inch rigid foam board (extruded polystyrene or polyiso) beneath new siding improves continuous wall R-value and flattens wavy old walls, adding $1.00 to $2.50 per square foot plus deeper window trim extensions.
  • Window, door, and gutter interfaces: Siding replacement routinely intersects with other exterior systems. Coordinating new cladding with window-replacement or sliding-glass-door-cost upgrades ensures integrated pan and head flashing, while removing and rehanging downspouts often overlaps with gutter-installation work.
  • Site access and landscaping: Tight urban lot lines, steep sloped yards, pools, or dense foundation plantings slow down ladder placement and material staging, increasing crew hours.

Hidden or extra costs to budget for

Initial ballpark estimates rarely capture every line item discovered once old cladding comes off the house. Setting aside a 10% to 15% contingency reserve covers the most frequent add-ons:

  • Old siding removal and haul-away ($0.70 – $2.00 / sq ft): Stripping existing siding and renting a 20- or 30-yard roll-off dumpster adds $1,750 to $5,000 on a 2,500-square-foot exterior. Installing new vinyl directly over flat existing siding skips tear-off, but most contractors recommend full removal so they can inspect the sheathing and install modern weather-resistive barriers.
  • Asbestos or lead-paint abatement ($3 – $10+ / sq ft): Homes built before 1978 may have lead-painted wood clapboards, and homes built between the 1920s and 1970s often have brittle asbestos-cement shingles. Certified encapsulation or hazardous-material removal adds $3,000 to $12,000+ depending on local environmental regulations.
  • Rotted OSB or plywood sheathing replacement ($2 – $5 / sq ft of affected area): Water trapped behind failed siding frequently rots the structural sheathing around window sills, rooflines, and bottom sill plates. Replacing damaged 4x8 sheets typically runs $75 to $150 per sheet installed.
  • House wrap, flashing, and seam tape ($0.50 – $1.25 / sq ft): Building codes require a continuous weather-resistive barrier (WRB) with taped seams and metal Z-flashing above horizontal trim boards and window heads.
  • Soffit, fascia, and trim board replacement ($6 – $15 / linear ft): Rot at roof eaves and rake boards often becomes visible only after old siding is stripped back.
  • Building permits ($150 – $600): Most municipalities require an exterior alteration permit to verify weather-barrier compliance, fire ratings, and wind-load fastening schedules.
  • Detaching and resetting exterior fixtures ($300 – $1,200): Removing and reinstalling exterior light sconces, house numbers, hose bibs, electrical meter boxes, satellite dishes, and garage-door-replacement perimeter trim takes licensed electrical or carpentry time.

DIY or hire

Full-house siding replacement is a major exterior envelope project where installation mistakes lead directly to hidden water intrusion and voided manufacturer warranties.

When DIY makes sense

  • Small single-story structures: Residing a detached shed, workshop, or single-story garage with vinyl or engineered wood panels is manageable for a skilled homeowner with a helper.
  • Ground-level accent walls: Installing decorative board-and-batten or faux stone panels on a front porch wall requires minimal ladder work.
  • Basic tool readiness: Vinyl siding requires relatively inexpensive tools—tin snips, a snap-lock punch, a zip tool, and a sliding compound miter saw with a fine-tooth plywood blade mounted backward.

When to hire a pro

  • Two-story or multi-gable homes: Working 20 to 30 feet off the ground while balancing 12-foot planks on pump jacks carries serious fall risk and requires OSHA-compliant staging.
  • Fiber cement or stucco installation: Fiber cement requires specialized shears or HEPA-filtered dust-extraction saws to avoid hazardous crystalline silica dust, plus strict clearance gaps (typically 6 inches above grade and 1 to 2 inches above roof flashing) to keep warranties valid.
  • Complex flashing details: Kickout flashing where roof eaves meet vertical walls, window head flashing, and ledger board flashing around attached decks (especially when coordinating with deck-building or fence-installation projects) require experienced weatherproofing execution.

Repair or replace

Choosing between targeted siding-repair work and a full exterior re-side comes down to the percentage of damaged wall area, material availability, and the age of your current cladding.

FactorChoose Siding Repair ($300 – $2,500)Choose Full Siding Replacement ($10,000 – $32,500)
Scope of DamageIsolated to fewer than 15%–20% of wall area (e.g., hail on one side, grill melt)Spread across multiple elevations or affecting 25%+ of exterior walls
Cladding AgeUnder 12–15 years old with sound underlying sheathingOver 20–30 years old and nearing the end of its service life
Color & Profile MatchOriginal manufacturer profile and color are still availableDiscontinued profile or severe UV fading makes patches obvious
Moisture & Structural HealthDry sheathing, firm framing, no interior water stainsSoft sheathing, recurring mold/mildew, or buckling across wall studs
Energy & Exterior PlansDrafts are minimal and no major window/door upgrades are plannedPairing with new windows, rigid foam insulation, or a full exterior remodel

Signs you need new siding

Exterior cladding often fails gradually from the back side out before dramatic holes appear on the surface. Watch for these physical indicators that replacement is overdue:

  • Warped, buckled, or loose panels: Vinyl that ripples excessively often was nailed too tightly, while wood or engineered planks that cup and pull away from studs indicate moisture absorption.
  • Soft, spongy, or rotted boards: Pressing a screwdriver gently near bottom courses, window sills, and corner trim should meet solid resistance; crumbling wood signals active fungal decay.
  • Peeling interior paint or wallpaper: Moisture bypassing failed exterior flashing or cracked caulk joints frequently migrates inward, causing bubbling paint on interior walls near windows.
  • Blistering or peeling exterior paint every 2 to 3 years: When wood or hardboard siding cannot hold a fresh paint job—making exterior-house-painting a recurring short-term fix—the substrate itself is usually failing.
  • Faded, chalky, or brittle cladding: Heavy UV exposure degrades older vinyl polymers until panels crack on light impact, and leaves a powdery chalk residue when rubbed by hand.
  • Higher heating and cooling bills: Gaps at seams, compressed insulation, and missing house wrap allow conditioned indoor air to escape and wind-driven drafts to penetrate wall cavities.
  • Insect tunnels or woodpecker holes: Carpenter ants, termites, and woodpeckers target softened wood and older cedar or hardboard siding.

Regional and climate considerations

Local weather patterns directly influence both material longevity and installation costs across the United States:

  • Coastal and hurricane-prone states (Florida, Gulf Coast, Carolinas): Building codes enforce strict high-wind uplift ratings (often 130 to 160+ mph), requiring thicker vinyl gauges (.044 to .046 inches), ring-shank stainless steel nails, tighter stud fastening schedules, and impact-rated fiber cement.
  • Wildfire-urban interface zones (California, Colorado, Pacific Northwest): Non-combustible Class A fire-rated cladding—such as fiber cement, stucco, brick veneer, or metal—is mandatory in many high-risk counties, ruling out untreated wood and standard vinyl.
  • Freeze-thaw and heavy snow regions (Midwest, Northeast, Mountain West): Cladding must tolerate wide seasonal temperature swings without cracking, and installers must maintain proper ground and roof-line clearances so snowpack does not wick moisture into wood or fiber cement edges.
  • Hot, humid climates (Southeast): Breathable rain-screen gaps (furring strips creating a 3/8-inch drainage plane behind the siding) help trapped vapor dry outward and prevent mold growth inside wall assemblies.
  • Labor market differences: Metropolitan areas in the Northeast, California, and Pacific Northwest typically run 15% to 30% above national averages due to higher crew wages, insurance, and dump fees, while the Southeast and parts of the Midwest often price 10% to 15% below national averages.

How to save money on siding replacement

You can reduce a whole-house siding quote by several thousand dollars without sacrificing weather protection or warranty coverage:

  • Schedule in late fall or winter: Exterior contractors hit peak demand from April through August. Booking a project between November and February often unlocks 5% to 15% off-season labor discounts.
  • Mix materials strategically: Install premium fiber cement, cedar shakes, or brick veneer accents on the street-facing front facade and gables, and use standard horizontal lap siding on the less-visible sides and rear elevation.
  • Keep the existing footprint and trim style: Avoiding structural bump-outs, complex belly bands, and intricate window pediments keeps labor hours predictable.
  • Choose standard stock colors: Manufacturers charge a premium and extend lead times for custom-tinted colors; selecting popular in-stock factory shades saves $0.50 to $1.50 per square foot.
  • Bundle exterior projects: Combining siding replacement with new windows, exterior doors, or gutters under one contractor eliminates duplicate scaffolding setups, dumpster deliveries, and flashing rework.
  • Compare at least three itemized bids: Written bids broken down by net square footage, material brand/thickness, tear-off, house wrap, and trim linear footage reveal inflated allowances immediately.

How to hire a siding contractor and questions to ask

A high-end siding material installed over poor flashing will fail faster than budget vinyl installed with meticulous waterproofing. Vet at least three local licensed exterior contractors before signing a deposit.

Vetting checklist

  1. Verify state licensing and insurance: Confirm active general or specialty exterior contractor licensing, general liability insurance, and workers' compensation coverage—critical when crews work on ladders and scaffolding.
  2. Check manufacturer certifications: Factory-certified installers (such as James Hardie Elite Preferred or VSI-certified vinyl installers) follow strict fastening and clearance rules that keep 30- to 50-year manufacturer warranties intact.
  3. Inspect local completed jobs: Ask for addresses of homes completed three to five years ago so you can inspect seam alignment, caulk joints, and window trim details in person.
  4. Insist on a line-item written scope: Avoid lump-sum one-line quotes; your contract should specify exact wall square footage, material grade, removal and disposal, house wrap brand, flashing type, and per-sheet plywood replacement rates.

Questions to ask before signing

  • Does this quote include full tear-off and disposal of the existing siding, or a layer-over?
  • What brand and thickness of house wrap, seam tape, and rigid insulation are included?
  • How will you flash window heads, door openings, and roof-to-wall intersections?
  • What is your per-sheet price if rotted plywood or OSB sheathing is uncovered after tear-off?
  • Will your crew use a rain-screen furring gap or install directly over the weather barrier?
  • Who pulls the municipal building permit, and is the permit fee included in this estimate?
  • What workmanship warranty do you provide in addition to the manufacturer's material warranty?

Common questions

Answers describe national planning ranges, not your house.

How much does it cost to replace siding on a 2,000 sq ft house?

Replacing siding on a house with 2,000 square feet of exterior wall area typically costs $8,000 to $26,000 installed in 2026, with a midpoint around $17,000. Keep in mind that a two-story home with 2,000 square feet of interior floor space often has 2,200 to 2,600 square feet of exterior wall area, which places total project costs closer to $10,000 to $32,500 depending on material and tear-off fees.

What is the cheapest siding to replace?

Standard horizontal vinyl siding is the most affordable cladding to install in 2026, averaging $4 to $12 per square foot installed, or $6,000 to $18,000 for 1,500 square feet of exterior wall area. Builder-grade .040-inch vinyl sits at the low end of that range, while thicker .044- to .046-inch and foam-backed insulated vinyl panels cost more upfront but resist dents and wind better.

Is it cheaper to paint or replace siding?

Exterior house painting is significantly cheaper upfront, typically costing $3,000 to $8,000 compared to $10,000 to $32,500 for full siding replacement. However, painting only makes financial sense if your existing cladding is structurally sound; if boards are rotted, warped, or peeling every few years due to trapped moisture, replacement prevents ongoing repair bills.

How long does it take to replace siding on a house?

A professional crew typically completes a whole-house siding replacement in 5 to 14 working days for an average 2,500-square-foot exterior wall area. Vinyl siding on a simple single-story home can finish in under a week, while heavy fiber cement, cedar shakes, extensive rot repair, or rainy weather can extend the schedule to two or three weeks.

Does new siding increase home value?

Yes, replacing worn or outdated siding consistently ranks among the highest-return exterior remodeling projects, typically recouping 75% to 88% of project costs at resale while boosting curb appeal and buyer confidence. Fiber cement and upscale vinyl or engineered wood upgrades deliver the strongest return on investment in most US housing markets.

Ranges for work that often shows up in the same season as this project.