Skip to content
US Home Costs

Exterior

Mobile Home Skirting Cost in 2026: Installed Prices Guide

Discover typical 2026 costs to install, replace, or repair mobile home skirting. Compare material prices, labor rates, and essential insulation options.

Updated November 10, 2026 · 10 min read · US Home Costs editorial desk

Planning range

National average installed cost range for a typical single-wide mobile home requiring roughly 150 linear feet of skirting perimeter. Includes standard materials, hardware, basic prep, and professional installation labor.

Typical planning range $1,500 to $5,000. National spread $630 to $6,500.

DIY or hire
Handy homeowners can install vinyl or metal skirting as a DIY project for $600 to $1,200 in materials. Masonry or sloped lots usually require professional installation.
Repair or replace
Minor hole repairs or single panel swaps run $100 to $400. Full replacement ($1,500 to $5,000) makes more sense when over 30 percent of the skirting is damaged or failing.

Installing or updating underpinning is one of the most effective exterior upgrades for a manufactured residence. Mobile home skirting cost ranges from $630 to $5,000 nationwide, with most homeowners spending between $1,500 and $5,000 for a professionally installed job. The national average sits right around $2,400 for a complete installation on a standard home.

Skirting serves a dual purpose: it boosts curb appeal by concealing the open foundation piers while forming a protective thermal and pest barrier. Unskirted or damaged underpinning exposes belly boards, floor insulation, and water supply lines to freezing winter air, rodent infestation, and wind damage. Understanding how materials, home dimensions, and site prep impact total pricing helps you establish an accurate budget for 2026.

Mobile home skirting cost at a glance

Total installed pricing varies primarily based on the perimeter of your home and the chosen material. A standard single-wide manufactured home typically requires about 150 linear feet of skirting material, while a double-wide home requires between 200 and 250 linear feet.

Mobile Home Unit TypeLinear Feet NeededTypical LowTypical HighNational Average
Single-Wide (14x70 to 16x80)150 LF$1,500$3,500$2,400
Double-Wide (24x60 to 32x80)200 - 250 LF$2,000$5,000$3,400
Triple-Wide / Multi-Section250 - 300+ LF$3,000$6,500$4,200

Material selection dramatically shifts where your final estimate lands within these overall ranges. Standard vinyl remains the budget-friendly baseline, whereas insulated panels, timber, and masonry products sit at the higher end of the pricing spectrum.

Mobile home skirting cost per linear foot

Because every home has a different perimeter, it helps to price skirting by the linear foot before you collect quotes. Basic panel stock runs about $6 to $8 per linear foot, so the material alone for a 150-foot single-wide perimeter comes to roughly $900 to $1,200 before trim, rails, vents, and access doors. Once labor is added, which is often around 60 percent of the job, installed totals for a single-wide usually land between $1,500 and $3,500.

PerimeterPanels only ($6-$8/LF)Typical installed total
150 LF (single-wide)$900 - $1,200$1,500 - $3,500
200 LF (smaller double-wide)$1,200 - $1,600$2,000 - $4,000
250 LF (larger double-wide)$1,500 - $2,000$2,500 - $5,000

Taller pier heights, sloped lots, and premium materials such as insulated vinyl, faux stone, or block push a project toward the top of these ranges, while a level lot with standard vinyl stays near the bottom.

What moves the price

Several structural and environmental factors dictate your final quote. Knowing these variables allows you to adjust scope before bringing out a contractor.

  • Home Perimeter and Pier Height: Skirting panel costs run $6 to $8 per linear foot for standard material stock. Homes elevated higher off the ground due to deep piers or steep slopes demand taller panels, increasing square footage requirements and material waste.
  • Material Composition: Non-insulated vinyl panels cost significantly less upfront than high-density insulated vinyl, pressure-treated timber, or poured concrete block.
  • Labor Rates and Regional Demand: Labor typically makes up roughly 60 percent of your overall installation budget. Handyman and siding professional rates range from $60 to $125 per hour depending on regional labor markets.
  • Site Grading and Ground Conditions: Sloped lots require individual panels to be custom-cut along the bottom edge to meet the grade. Rocky or uneven ground increases labor time for setting top and bottom receiver tracks.
  • Old Skirting Removal and Disposal: Tearing down and hauling away existing, rotted, or storm-damaged underpinning adds $200 to $500 to the total bill.
  • Vents and Egress Access Doors: Code requires adequate crawl space ventilation and access points for plumbing repairs. Adding access doors adds $50 to $85 each, while foundation vents cost $7 to $25 per vent.

Material cost breakdown

The table below outlines installed cost ranges by material type for standard single-wide (~150 linear feet) and double-wide (~200 to 250 linear feet) manufactured homes.

Skirting MaterialSingle-Wide Cost (Installed)Double-Wide Cost (Installed)Durability & Maintenance
Standard Vinyl$630 – $1,090$1,100 – $1,550Low to Moderate; prone to lawnmower cracks
Faux Stone$660 – $1,000$920 – $1,350Moderate; high visual appeal, lightweight
Faux Brick$800 – $1,500$1,200 – $1,980Moderate; attractive finish, easy panel install
Brick or Concrete Block$700 – $1,000$1,400 – $2,000High; permanent installation, excellent strength
Timber / Composite Wood$1,500 – $2,000$3,000 – $4,000Moderate to High; requires sealing or staining
Insulated Vinyl$1,440 – $4,000$1,760 – $4,480High; maximum thermal protection for cold zones

Labor vs materials breakdown

When budgeting for manufactured home skirting cost, labor accounts for approximately 60 percent of the total project price, while materials and hardware make up the remaining 40 percent.

On a typical $2,400 single-wide project:

  • Materials & Accessories: $960 (panels, top track, bottom channel, ground stakes, screws, vents, access door)
  • Labor & Site Prep: $1,440 (site measurement, track installation, panel trimming, secure anchoring, cleanup)

Contractors generally complete a standard single-wide installation within 6 to 10 working hours. However, sites requiring site grading, old skirt demolition, or masonry mortar work require multiple days, driving up labor expenditures.

Hidden or extra costs

Project quotes do not always capture accessories or site modifications required by municipal building codes or HUD guidelines. Watch for these potential add-ons:

  • Access Egress Doors ($50 to $85 each): HUD code mandates at least one removable crawl space door for utility access. Most installers include one door, but larger double-wides often need two.
  • Automatic or Manual Foundation Vents ($7 to $25 each): To prevent moisture accumulation and mold, code requires 1 square foot of ventilation for every 150 square feet of floor area.
  • Corner Trim and Receiver Channels ($15 per corner piece): Finishing pieces for faux brick or vinyl corners create a clean look and prevent wind blow-offs.
  • Soil Trenching ($150 to $400): In high-wind areas, installers dig a shallow trench around the perimeter to bury the bottom ground track, preventing wind up-drafts from popping panels out of alignment.
  • Ground Moisture Barriers ($200 to $450): Laying 6-mil polyethylene plastic sheeting across the dirt underneath your home prevents soil moisture from evaporating up into your floor joists.

Signs you need the work

Mobile home skirting is your structure's primary defense against weather elements and animal intrusion. You should plan for replacement or major repair when you notice:

  • Freezing Water Pipes: If supply lines freeze during routine winter cold snaps, your underpinning has lost its thermal seal or developed large air gaps.
  • Visible Buckling or Wind Blow-Outs: Warped, cracked, or missing panels allow wind to scoop underneath the structure, threatening floor insulation panels.
  • Rodent or Pest Activity: Smells, torn under-home belly wrap insulation, or droppings point to gaps along the bottom receiver channel.
  • Excessive Moisture or Odors: Damp air rising into living areas indicates inadequate foundation ventilation or failing moisture protection underneath.
  • Weed Eater Damage: Repeated hits from lawn trimmers shatter older, brittle vinyl panels around the ground line.

Repair or replace

Determining whether to perform a mobile home skirting repair cost fix or execute a full system tear-out comes down to structural integrity and overall coverage area.

When to repair

If damage is isolated to a few panels from lawnmower impacts or a fallen tree branch, simple repairs make financial sense. Handyman repair costs run $100 to $400.

  • Replacing 2 to 4 damaged vinyl panels: $80 to $150 in materials and quick labor.
  • Re-securing loose top or bottom track channels after a storm: $100 to $200.
  • Replacing a broken access door or rusted vent: $50 to $120.

When to replace

Full replacement ($1,500 to $5,000) becomes necessary when:

  • More than 25 to 30 percent of total perimeter panels are cracked, missing, or sun-faded beyond matching.
  • The original system lacks insulation, and winter heating bills are rising.
  • You are upgrading your exterior siding, installing a new porch, or scheduling vinyl-siding-installation or exterior-house-painting to overhaul curb appeal.
  • The bottom framing or track has rotted or pulled away from the home's steel frame.

DIY or hire

Homeowners frequently consider installing mobile home skirting themselves to save on installation labor.

Doing it yourself

Installing standard vinyl or corrugated metal panels is an accessible DIY task for homeowners with basic carpentry tools. A DIY install on a single-wide home typically costs $600 to $1,200 for panel kits, channels, and fasteners.

Key challenges include setting a perfectly level top track along the home's rim joist and measuring individual panel height cuts along uneven ground. You will need a water level or laser level, utility knife, tin snips, tape measure, hammer, and protective eyewear.

Hiring a professional

Complex installations should be handled by professional siding or manufactured home specialists. Hire a pro if:

  • You choose heavy masonry materials like brick, concrete block, or real stone that require footings and mortar.
  • Your site has a steep grade or rocky soil that complicates bottom track anchoring.
  • You want insulated vinyl skirting installed to meet specific local energy codes.
  • You lack the time or tools to trim dozens of panels accurately.

Professional installers ensure proper expansion gaps for seasonal temperature swings, preventing vinyl panels from warping or popping loose during high-wind storms.

Regional and climate notes

Climate plays a decisive role in choosing the right manufactured home underpinning.

  • Northern & Cold Climates: Insulated mobile home skirting cost ($1,440 to $4,480) carries a higher initial price tag but prevents costly pipe bursts during extreme freeze cycles. Pair your installation with pipe-insulation-cost upgrades and house-winterization-cost services for maximum freeze defense. Insulated panels maintain ground-heat retention under your subfloor.
  • High-Wind & Coastal Zones: Standard thin vinyl easily blows out in 50+ mph wind gusts. Coastal and Plains regions benefit from heavy-gauge vinyl, metal, or masonry skirting anchored into concrete footings or buried ground tracks.
  • Humid & Southern Regions: Moisture management is critical in warm climates. Ensure your installation meets HUD ventilation ratios (1:150 square feet) or incorporates automatic temperature-controlled vents to minimize mold growth. Combining adequate venting with rodent-removal inspections ensures open vents do not become critter entry points.

How to save money

Lowering your total project cost does not mean sacrificing structural protection. Use these practical strategies to stretch your budget:

  • Keep Existing Sub-Framing: If your current wooden mounting frame or aluminum top tracks remain structurally sound, ask your contractor to mount new panels to the existing framework. This trims $200 to $400 off labor and material fees.
  • Handle Demolition Yourself: Unclipping old vinyl panels and hauling them to a local disposal site saves the $200 to $500 fee charged for professional tear-out.
  • Buy Complete Skirting Kits: Manufacturers package panels, top front trim, top back track, bottom channel, and ground spikes into bundled kits tailored to common single-wide (e.g., 14x70, 16x80) and double-wide footprints. Kits run 10 to 20 percent cheaper than purchasing individual components piecemeal.
  • Schedule During Off-Peak Months: Siding and manufactured home contractors experience peak demand in spring and summer. Scheduling your job in late fall or winter often yields better labor rates.
  • Combine Exterior Work: Bundle your skirting job with other planned exterior improvements like gutter-installation, deck-building, fence-installation, or garage-door-replacement to minimize contractor trip fees.

How to hire a contractor and questions to ask

Selecting a contractor experienced in manufactured housing ensures your skirting stays secure and compliant with local building standards.

How to locate qualified installers

Seek out licensed siding contractors, handyman services specializing in mobile home repairs, or licensed manufactured home setup crews. Confirm they carry active general liability and worker's compensation insurance before allowing them on site.

Key questions to ask before signing

  1. Are you familiar with HUD crawl space ventilation and access door codes for mobile homes?
  2. Does your quote include ground-leveling, trenching, or bottom channel anchoring?
  3. Does the price cover old skirting removal and hauling fees?
  4. What thickness or gauge of skirting material do you recommend for my climate zone?
  5. How do you secure panels against high winds and lawn-trimmer impacts?
  6. Will you need to build a wooden ground frame, or are you mounting directly to the home's rim joist?
  7. What warranty do you offer on labor and wind blow-out resistance?

Common questions

Answers describe national planning ranges, not your house.

How much does mobile home skirting cost on average?

Installing mobile home skirting costs an average of $2,400 nationwide. Most single-wide and double-wide homeowners spend between $1,500 and $5,000 for materials and professional labor combined. Total pricing depends heavily on home perimeter size, ground slope, and whether you choose basic vinyl or insulated panels.

Is insulated mobile home skirting worth the extra cost?

Yes, insulated mobile home skirting ($1,440 to $4,480 installed) is highly worthwhile in cold climates. It creates a thermal barrier that keeps plumbing lines beneath your subfloor from freezing during harsh winter weather. The initial higher investment is offset over time through lower heating bills and reduced risk of costly frozen pipe repairs.

How many linear feet of skirting do I need for a single-wide mobile home?

A standard single-wide mobile home typically requires approximately 150 linear feet of skirting panels. To calculate your exact needs, measure all exterior sides of your home and add the totals together. Be sure to purchase 10 percent extra material to account for corner trimming and ground grade adjustments.

Can I install mobile home skirting myself to save money?

DIY installation of standard vinyl or corrugated metal skirting can save you 50 to 60 percent on overall project costs. Materials for a DIY single-wide job cost around $600 to $1,200. However, if your home sits on a steep slope, requires masonry brickwork, or needs complex ground trenching, hiring a professional ensures proper wind-anchoring and alignment.

Ranges for work that often shows up in the same season as this project.